This product is no longer available and has been replaced by: CM106B.
| 利用できるサービス | |
|---|---|
| 修理 | 非対応 |
| キャリブレーション | 非対応 |
| フリーサポート | 非対応 |
概要
The CM106 is an adjustable tripod made of galvanized steel tubing. It is adjustable from 7 to 10 ft, so it replaces the 6 ft CM6 and the 10 ft CM10. It is also lighter than those tripods because it is made with tubing and they are made with pipe. The CM106 is a general purpose tripod that can be used for mounting sensors, solar panels, antennas, and instrument enclosures.
続きを読む利点と特徴
- Support for meteorological sensors, hydrological sensors, sensor mounts, solar panels, environmental enclosures
- Portable instrument mount
- Lightning and grounding rods, grounding cables, grounding cable clamps, ground stakes, and UV-resistant cable ties included
- Enclosures can be mounted on tripod leg, as well as mast
イメージ
詳細
The CM106 is constructed with individually adjusted legs that allow installation over uneven terrain. Height of the mast is 2.1 m (7 ft), or 3 m (10 ft) with the mast extended.
The CM106 includes lightning and grounding rods, grounding cables, UV resistant cable ties, and stakes for securing the tripod feet to the ground. An optional guy kit is recommended for sites that may experience high wind speeds. (See Allowable Wind Speeds in the Specifications.) Instrument enclosures can be purchased with mounting brackets that attach to either the mast or leg base.
The CM106 can be used for a variety of applications. For meteorological stations, sensors are mounted to the tripod using mounting brackets appropriate for the model of sensor. For nonmeteorological applications, the tripod can be used to mount instrument enclosures, solar panels, junction boxes, or antennas.
| The CM106 replaced the CM6 and CM10 tripods. Improvements over the CM6/CM10 include using galvanized tubing instead of galvanized pipe which weighs less, and the ability to mount our enclosures on the CM106 leg base. |
仕様
| Vertical Load Limit | 45 kg (100 lb) |
| Leveling Adjustment | Slide collars on each leg adjust individually. |
| Maximum Slope Angle | 22° or 40% grade (Maximum slope angle assumes that the leg clamp pins are engaged in the holes under the legs, and that one leg points downhill while the other two legs point uphill.) |
| Leg Base | 10.16 x 12.7 cm with four 1.58 cm hole for stakes (4 x 5 in. with four 0.62 in. holes for stakes) |
| Base Diameter | 2.8 m (9.3 ft) |
| Main Lower Mast Outer Diameter | 48 mm (1.90 in.) |
| Retractable Upper Mast Outer Diameter | 44 mm (1.74 in.) |
| Weight with Mast | 18 kg (40 lb) |
Measurement Height |
|
| Upper Mast Retracted | 2.1 m (7 ft) |
| Upper Mast Extended | 3 m (10 ft) |
Maximum Allowable Sustained Wind |
|
| -NOTE- |
Allowable sustained wind and wind gust values assume the following:
|
| Mast Extended |
|
| Mast Retracted |
|
Maximum Allowable Wind Gust |
|
| -NOTE- |
Allowable sustained wind and wind gust values assume the following:
|
| Mast Extended |
|
| Mast Retracted |
|
互換性
注意： 以下は代表的な互換性情報を示しています。互換性のある製品や互換性のない製品をすべて網羅したリストではありません。
互換性に関する追加情報
Enclosure Brackets
Mast
The “-MM” mount option for our environmental enclosures is intended for mounting the enclosure to a tripod's mast. An enclosure ordered with this option will be shipped with a three-piece bracket mounted to the top of the enclosure and an identical three-piece bracket mounted to the bottom of the enclosure.
Leg Base
All of our standard enclosures (including the ENC16/18) can be mounted to the CM106's leg base. The "-LM" mount option for our environmental enclosures allows the enclosure to be attached to the leg base of the CM106. This option includes a metal flange, two brackets, and a 2.5" u-bolt. The brackets attach to the right and left side of the enclosure, and the flange attaches to the tripod near the mast. The flange fits into a notch in one of the brackets, and the other bracket connects to a tripod leg via the u-bolt.
ドキュメント
よくある質問
CM106に関するよくある質問の数： 1
-
To provide additional support for the mast in areas that experience high wind speeds, order the optional guy kit for the CM106 (pn 27117). Refer to the Specifications information on the CM106 product page, which describes a guy kit’s effect on the “Maximum Allowable Sustained Wind” and the “Maximum Allowable Wind Gust” of a CM106.
記事とプレスリリース
Privacy Policy Update
We've updated our privacy policy. 詳細はこちら
Cookie Consent
Update your cookie preferences. クッキーの設定を更新する