ET107 は、芝生や商業農業用途の灌漑スケジュール用に設計された自動気象ステーションです。このステーションは、蒸発と植物の蒸散により土壌から失われる水の量である潜在蒸発散量 (ETo) を計算します。蒸発散率を計算すると、水やりをしすぎずに十分な水を供給する灌漑スケジュールの作成に役立ちます。
続きを読む当社の ET107 ETo ステーションは、気象センサ、アルミニウム製の 3 m ポール、CR1000M モジュールと 7 Ahr の密閉型充電式バッテリを収納する環境屋外収納ケースで構成されています。バッテリは、AC 電源または 10 W のソーラーパネルで充電します。屋外収納ケースの外側には密閉型円形コネクタが付いており、センサの接続が簡単です。
ET107 に含まれる気象センサは、CS305-ET 太陽放射センサ、HMP60-ETS 気温および相対湿度プローブ、TE525-ET 転倒マス雨量計、および 034B-ETM 風セットまたは WindSonic1-ETM 2-D 超音波風センサのいずれかです。
ET107 は、次のものも測定できます:
-注意- |
ET107 には独自の仕様を持つコンポーネントがあります。 これらの仕様を確認するには、以下の適切な製品を参照してください。 |
ET107 の交換用センサには、-ET または -ETM の接尾辞が付いています。これらのセンサは、注文の下にリストされています。
ET107 は、次の測定も可能です:
One default program is for an ET107 with the 034B wind sensor and another default program is for an ET107 with a WindSonic1.
The ETsz() instruction requires the user to input lattitude, longitude, elevation, and crop type for a station's location in order to generate accurate calculations of ET. The Generic_ET_107_ETsz.CR1 and Generic_ET_107_ETsz_Windsonic.CR1 programs use the ConstTable() intruction to create a constants table that allows the user to easily input these values using Loggernet, PC400, or a keyboard display. These values only need to be set once, during station set up.
ET107に関するよくある質問の数: 18
すべて展開すべて折りたたむ
Refer to the “Maintenance, Troubleshooting, and Schematics” section of the ET107 Weather Station Instruction Manual for procedural instructions.
Calsense Command Center software can interface with Campbell Scientific’s VisualWeather software, which can retrieve values from the ET107. In the Command Center software, setting up a station involves connecting to the VisualWeather LoggerNet server and selecting variables from the weather station’s listing for wind speed, rainfall, and ETo.
The PS100 power supply that’s in the ET107 specifies a charging voltage of 15 to 28 Vdc or 18 Vac RMS. A 24 Vac transformer will blow the protective circuitry in the PS100.
Yes. However, special data logger programming is required. Contact an application engineer at Campbell Scientific for assistance.
VisualWeather を ET107、T107 (Toro)、ET106、または MetData1 で使用し、ステーションが標準構成である場合、VisualWeather でのステーションの設定は比較的簡単です。Weather Station Network 画面のリストからステーションを選択すると、ほとんどの作業が自動的に実行されます。
ただし、カスタム ステーション、異なるステーション モデル、またはセンサーの 1 つに異なるバリエーションを使用する場合は、ウェザー ステーション ネットワーク設定画面でカスタム ステーションを設定する必要があります。ステーション選択画面で、[Custom] を選択します。
ステーションの詳細を尋ねる画面に従います。次に、VisualWeather はステーションに接続し、データが保存されているステーションのデータ テーブルの名前とフィールドを取得します。これらのテーブルの名前とフィールドは VisualWeather にとって意味がないため、マッピング プロセスを使用して、データ テーブル フィールドを VisualWeather が認識するフィールドと単位にマッピングする必要があります。このマッピングにより、VisualWeather は意味のある画面とレポートを作成できます。
データ テーブルは多くの場合番号で識別され、フィールドはわかりにくいことが多いため、マッピング プロセスがわかりにくい場合があります。カスタム ステーションのフィールドをマッピングするには、Campbell Scientific に問い合わせてサポートを受けてください。
Wind speed, wind direction, solar radiation, temperature, relative humidity, and rain measurements are data parameters that are available. Typically, ETo is calculated by the software; however, it is possible for the ET107 to perform the calculation as well.
The most significant difference is that the retired ET106 used the CR10X datalogger, whereas the ET107 uses the CR1000 datalogger. Other differences are the following:
いいえ。VisualWeather は別途購入する必要があります。
The communications options include direct serial connection, short haul modem, analog phone modem, cellular phone modem, radio, and Wi-Fi. Also, with an enclosure alteration, an Ethernet port can be added.
Note: Some of the listed telemetry options can drastically alter the power budget of the station.
We've updated our privacy policy. 詳細はこちら
Update your cookie preferences. クッキーの設定を更新する