Tell the CR1000X Series what you need it to do.

Create a program and wire your sensors.

Short Cut is a simple way to generate a program and wiring diagram. CRBasic Editor lets you look under the hood.

View the steps.



Make sure to follow your wiring diagram.



Looking for product information? Go here: CR1000X Measurement and Control Datalogger


View CR1000X Page

CR1000X Support Resources

  1. New CR1000X Datalogger (2:26)
  2. CR1000X Series Getting Started
  3. Datalogger Programming
  4. Connect Window Tutorial
  5. View Data Tutorial
  6. Collect Data Tutorial
  7. CR1000X Datalogger Getting Started | Overview (Part 1) (1:52)
  8. CR1000X Datalogger Getting Started | Communicate (Part 2) (5:24)
  9. CR1000X Datalogger Getting Started | Program (Part 3) (5:49)
  10. CR1000X Datalogger Getting Started | Data (Part 4) (3:47)
  11. Empezar CR1000X (Spanish) | Introduccion (Parte 1/4) (2:30)
  12. Empezar CR1000X (Spanish) | Comunicacion (Parte 2/4) (7:36)
  13. Empezar CR1000X (Spanish) | Programacion (Parte 3/4) (8:11)
  14. Empezar CR1000X (Spanish) | Envio de programa, Descarga y Monitorizacion de datos (Parte 4/4) (5:20)
  15. Fundamentals of CRBasic Programming Part 1: Variables (13:30)
  16. Fundamentals of CRBasic Programming Part 2: Tables (8:53)
  17. Fundamentals of CRBasic Programming Part 3: Writing a Complete Program (14:51)
  18. Fundamentals of CRBasic Programming Part 4: Programming for Control with Operators and Logical Expressions. (9:05)
  19. Fundamentals of CRBasic Programming Part 5: Conditional Tables (10:51)
  20. Fundamentals of CRBasic Programming Part 6: Loops (9:02)
  21. Fundamentals of CRBasic Programming Part 7:Determine If External Memory is Required/Intro to MicroSD (9:19)
  22. Fundamentals of CRBasic Programming Part 8: Deploy, Monitor, and Swap MicroSD Cards in the Field (7:41)
  23. Fundamentals of CRBasic Programming Part 9: Retrieving Data from a MicroSD Card (5:51)
  24. CRBasic in the Real World Part 1: Adding a Water Level Measurement (8:28)
  25. CRBasic in the Real World Part 2: Triggering Real-Time Measurements During a Site Visit (10:41)
  26. CRBasic in the Real World Part 3: Subroutines (6:31)
  27. CRBasic in the Real World Part 4: Offsets (7:24)
  28. CRBasic in the Real World Part 5: Changing the Sensor Used in a Program and Program Versioning (5:42)
  29. Sending an OS to a Local Datalogger (Part 1) (5:28)
  30. Sending an OS to a Remote Datalogger (Part 2) (5:10)
  31. IP Networking and Data Loggers Part 1 (8:34)
  32. IP Networking and Data Loggers Part 2 (9:51)
  33. Ethernet over USB (2:11)
  34. LoggerNet Software | Changing Variables (2:33)
  35. LoggerNet Software | Network Planner (4:04)
  36. Pipeline and Sequential Modes (10:04)
  37. Double-Precision Calculations (5:50)
  38. Toolbox for Installation and Maintenance (2:21)
  39. Power Budgeting (4:07)
  40. Understanding the Importance of Grounding (5:41)
  41. Replacing the CR1000X Lithium Battery (5:58)
  42. Certificates of Calibration (1:05)
  43. Campbell Scientific Data Logger Expansion (8:53)
  44. Using a Multiplexer (8:27)
  45. Multiplexer Programming with a CR1000 Datalogger (6:09)
  46. Wiring a Datalogger to a Multiplexer (7:18)
  47. LoggerLink Software | An Introduction (12:11)
  48. Troubleshooting Resistance-Based Sensors (18:23)
  49. Troubleshooting Voltage Output Sensors (7:42)
  50. SDI-12 Sensors | Transparent Mode (7:13)
  51. SDI-12 Sensors | Watch or Sniffer Mode (3:25)
  52. Using RTMC (2023) (10:41)
  53. Using RTMC Pro (5:44)
  54. Using RTMC Pro to Create a Report and Hotspot (6:45)
  55. Basic Troubleshooting 1: Measuring Data Logger Output Voltage With a Multimeter (3:54)
  56. Basic Troubleshooting 2: Checking Continuity (2:15)
  57. Basic Troubleshooting 3: Measuring Current Drain (4:12)
  58. Troubleshooting Communications Issues with LogTool (6:40)
  59. Introduction to the CR1000KD (2:44)
  60. Troubleshooting with the CR1000KD (7:12)
  61. CRBasic Functions (6:23)
  62. Backing Up and Restoring Data Logger Settings Files Using Device Configuration (4:07)
  63. Creating Custom Menus in CRBasic for a Data Logger Display (8:28)
  64. Creating a Short Cut Wiring Diagram for Sensor Not in Short Cut (5:50)
  65. Wiring Diagrams for Data Logger Programs Part 1: Using Short Cut for Windows (5:28)
  66. Analyzing a CRBasic Program to Deduce Sensor Wiring (7:13)
  67. Documenting Data Logger Wiring Using an Excel Template (5:41)