Set Up Your Software for Ethernet Communication

Your software needs to be set up to communicate with the datalogger over IP as well. The software IP settings need to match those set in the datalogger, which is why a static IP address is recommended. 

  • IP Address, 
  • Subnet Mask, and 
  • IP Gateway. 

The EZSetup Wizard makes it easy. 

View the steps.

Looking for product information? Go here: CR1000X Measurement and Control Datalogger


View CR1000X Page

CR1000X Support Resources

  1. New CR1000X Datalogger (2:26)
  2. CR1000X Series Getting Started
  3. Datalogger Programming
  4. Connect Window Tutorial
  5. View Data Tutorial
  6. Collect Data Tutorial
  7. CR1000X Datalogger Getting Started | Overview (Part 1) (1:52)
  8. CR1000X Datalogger Getting Started | Communicate (Part 2) (5:24)
  9. CR1000X Datalogger Getting Started | Program (Part 3) (5:49)
  10. CR1000X Datalogger Getting Started | Data (Part 4) (3:47)
  11. Empezar CR1000X (Spanish) | Introduccion (Parte 1/4) (2:30)
  12. Empezar CR1000X (Spanish) | Comunicacion (Parte 2/4) (7:36)
  13. Empezar CR1000X (Spanish) | Programacion (Parte 3/4) (8:11)
  14. Empezar CR1000X (Spanish) | Envio de programa, Descarga y Monitorizacion de datos (Parte 4/4) (5:20)
  15. Fundamentals of CRBasic Programming Part 1: Variables (13:30)
  16. Fundamentals of CRBasic Programming Part 2: Tables (8:53)
  17. Fundamentals of CRBasic Programming Part 3: Writing a Complete Program (14:51)
  18. Fundamentals of CRBasic Programming Part 4: Programming for Control with Operators and Logical Expressions. (9:05)
  19. Fundamentals of CRBasic Programming Part 5: Conditional Tables (10:51)
  20. Fundamentals of CRBasic Programming Part 6: Loops (9:02)
  21. Fundamentals of CRBasic Programming Part 7:Determine If External Memory is Required/Intro to MicroSD (9:19)
  22. Fundamentals of CRBasic Programming Part 8: Deploy, Monitor, and Swap MicroSD Cards in the Field (7:41)
  23. Fundamentals of CRBasic Programming Part 9: Retrieving Data from a MicroSD Card (5:51)
  24. CRBasic in the Real World Part 1: Adding a Water Level Measurement (8:28)
  25. CRBasic in the Real World Part 2: Triggering Real-Time Measurements During a Site Visit (10:41)
  26. CRBasic in the Real World Part 3: Subroutines (6:31)
  27. CRBasic in the Real World Part 4: Offsets (7:24)
  28. CRBasic in the Real World Part 5: Changing the Sensor Used in a Program and Program Versioning (5:42)
  29. Sending an OS to a Local Datalogger (Part 1) (5:28)
  30. Sending an OS to a Remote Datalogger (Part 2) (5:10)
  31. IP Networking and Data Loggers Part 1 (8:34)
  32. IP Networking and Data Loggers Part 2 (9:51)
  33. Ethernet over USB (2:11)
  34. LoggerNet Software | Changing Variables (2:33)
  35. LoggerNet Software | Network Planner (4:04)
  36. Pipeline and Sequential Modes (10:04)
  37. Double-Precision Calculations (5:50)
  38. Toolbox for Installation and Maintenance (2:21)
  39. Power Budgeting (4:07)
  40. Understanding the Importance of Grounding (5:41)
  41. Replacing the CR1000X Lithium Battery (5:58)
  42. Certificates of Calibration (1:05)
  43. Campbell Scientific Data Logger Expansion (8:53)
  44. Using a Multiplexer (8:27)
  45. Multiplexer Programming with a CR1000 Datalogger (6:09)
  46. Wiring a Datalogger to a Multiplexer (7:18)
  47. LoggerLink Software | An Introduction (12:11)
  48. Troubleshooting Resistance-Based Sensors (18:23)
  49. Troubleshooting Voltage Output Sensors (7:42)
  50. SDI-12 Sensors | Transparent Mode (7:13)
  51. SDI-12 Sensors | Watch or Sniffer Mode (3:25)
  52. Using RTMC (2023) (10:41)
  53. Using RTMC Pro (5:44)
  54. Using RTMC Pro to Create a Report and Hotspot (6:45)
  55. Basic Troubleshooting 1: Measuring Data Logger Output Voltage With a Multimeter (3:54)
  56. Basic Troubleshooting 2: Checking Continuity (2:15)
  57. Basic Troubleshooting 3: Measuring Current Drain (4:12)
  58. Troubleshooting Communications Issues with LogTool (6:40)
  59. Introduction to the CR1000KD (2:44)
  60. Troubleshooting with the CR1000KD (7:12)
  61. CRBasic Functions (6:23)
  62. Backing Up and Restoring Data Logger Settings Files Using Device Configuration (4:07)
  63. Creating Custom Menus in CRBasic for a Data Logger Display (8:28)
  64. Creating a Short Cut Wiring Diagram for Sensor Not in Short Cut (5:50)
  65. Wiring Diagrams for Data Logger Programs Part 1: Using Short Cut for Windows (5:28)
  66. Analyzing a CRBasic Program to Deduce Sensor Wiring (7:13)
  67. Documenting Data Logger Wiring Using an Excel Template (5:41)