Get Started.

Unpack your shipping boxes.

The CR300 ships with:

  • Certificate of Calibration
  • USB Cable
  • Screwdriver
  • Type T Thermocouple
  • Screws and Grommets for mounting (3 each)

Install your software.

The CR300 is compatible with LoggerNet, PC400, and PC200W (versions 4.4 or higher).

Looking for product information? Go here: CR310 Measurement and Control Datalogger


View CR310 Page

CR310 Support Resources

  1. CR300 and CR310 Getting Started Tutorial
  2. Power Budgeting (4:07)
  3. Connect Window Tutorial
  4. Collect Data Tutorial
  5. RF Communication QuickStart
  6. CR300 Datalogger QuickStart (Part 1) (1:47)
  7. CR300 Datalogger QuickStart (Part 2) (5:19)
  8. CR300 Datalogger QuickStart (Part 3) (5:36)
  9. CR300 Datalogger QuickStart (Part 4) (3:31)
  10. Certificates of Calibration (1:05)
  11. View Data Tutorial
  12. Hughes 9502 Inmarsat BGAN Satellite IP Terminal (13:08)
  13. SDI-12 Sensors | Watch or Sniffer Mode (3:25)
  14. Sending an OS to a Local Datalogger (Part 1) (5:28)
  15. Sending an OS to a Remote Datalogger (Part 2) (5:10)
  16. Fundamentals of CRBasic Programming Part 6: Loops (9:02)
  17. Fundamentals of CRBasic Programming Part 7:Determine If External Memory is Required/Intro to MicroSD (9:19)
  18. Fundamentals of CRBasic Programming Part 8: Deploy, Monitor, and Swap MicroSD Cards in the Field (7:41)
  19. Fundamentals of CRBasic Programming Part 9: Retrieving Data from a MicroSD Card (5:51)
  20. Fundamentals of CRBasic Programming Part 1: Variables (13:30)
  21. Fundamentals of CRBasic Programming Part 2: Tables (8:53)
  22. Fundamentals of CRBasic Programming Part 3: Writing a Complete Program (14:51)
  23. CRBasic in the Real World Part 1: Adding a Water Level Measurement (8:28)
  24. CRBasic in the Real World Part 2: Triggering Real-Time Measurements During a Site Visit (10:41)
  25. CRBasic in the Real World Part 3: Subroutines (6:31)
  26. CRBasic in the Real World Part 4: Offsets (7:24)
  27. CRBasic in the Real World Part 5: Changing the Sensor Used in a Program and Program Versioning (5:42)
  28. EZSetup Ethernet Connection (2:02)
  29. Ethernet over USB (2:11)
  30. Built-in Web Interface (2:59)
  31. Toolbox for Installation and Maintenance (2:21)
  32. Datalogger Programming
  33. Datalogger Ethernet Configuration (2:54)
  34. Troubleshooting Resistance-Based Sensors (18:23)
  35. Troubleshooting Voltage Output Sensors (7:42)
  36. Pipeline and Sequential Modes (10:04)
  37. Double-Precision Calculations (5:50)
  38. LoggerNet Software | Changing Variables (2:33)
  39. Understanding the Importance of Grounding (5:41)
  40. Using RTMC (2023) (10:41)
  41. Using RTMC Pro (5:44)
  42. Using RTMC Pro to Create a Report and Hotspot (6:45)
  43. Basic Troubleshooting 1: Measuring Data Logger Output Voltage With a Multimeter (3:54)
  44. Basic Troubleshooting 2: Checking Continuity (2:15)
  45. Basic Troubleshooting 3: Measuring Current Drain (4:12)
  46. Introduction to the CR1000KD (2:44)
  47. Wiring Diagrams for Data Logger Programs Part 1: Using Short Cut for Windows (5:28)
  48. Analyzing a CRBasic Program to Deduce Sensor Wiring (7:13)
  49. Documenting Data Logger Wiring Using an Excel Template (5:41)