RETIRED ›
This product is no longer available and has been replaced by: CR350.
CR850 Measurement and Control Datalogger
利用できるサービス
修理 対応
キャリブレーション 対応
フリーサポート 対応

概要

The CR850 is a smaller, research-grade data logger that includes an on-board keyboard display as part of its integrated package. It is intended for smaller configurations in which fewer sensors will be measured. Each CR850 reads input from sensors, then transmits the data via a communication peripheral; most sensors and telecommunication devices are compatible. Multiple CR850s can be configured as a network or units can be deployed individually. This rugged data logger can provide stand-alone operation in harsh, remote environments.

続きを読む

利点と特徴

  • Integrated keyboard and display screen let you program, manually initiate data transfers, and view data, all on site.
  • Ideal applications include wind profiling, weather stations, ETo/agriculture, air quality, soil moisture, water level/stage, aquaculture, vehicle testing, Time Domain Reflectometry, SCADA, and water quality
  • Simpler in design, the CR800 and CR850 are easier to program and wire.
  • Serial communications with serial sensors and devices supported via I/O port pairs
  • Contains custom ASIC chip that expands pulse count, control port, and serial communications capabilities
  • Supports PakBus, Modbus, SDI-12, and DNP3 protocols
  • Compatible with channel expansion peripherals allowing you to expand your system
  • Includes both an CS I/O port and an RS-232 port for connecting communication devices
  • Gas Discharge Tube (GDT) protected inputs
  • Battery-backed clock that ensures accurate time is maintained while data logger is disconnected from battery power
  • Program with LoggerNet, PC400, or Short Cut to fit your setup

イメージ

詳細

The CR850 consists of measurement electronics encased in a plastic shell with an integrated wiring panel, 16- character keyboard, and display screen. The display can show 8 lines x 21 characters (64 x 128 pixels). Custom menus are supported allowing customers to set up choices within the data logger program that can be initiated by a simple “toggle” or “pick list”. Its keyboard and display screen is used to program the data logger, manually initiate data transfer, and display data.

The CR850 uses an external  power supply. Low power consumption allows the it to operate for extended periods on a battery recharged with a solar panel—eliminating the need for AC power. The CR850 suspends execution when primary power drops below 9.6 V, reducing the possibility of inaccurate measurements.

The on-board operating system includes measurement, processing, and output instructions for programming the data logger. The programming language, CRBasic, uses a BASIC-like syntax. Measurement instructions specific to bridge configurations, voltage outputs, thermocouples, and pulse/frequency signals are included. Processing instructions support algebraic, statistical, and transcendental functions for on-site processing. Output instructions process data over time and control external devices.

仕様

-NOTE- Note: Additional specifications are listed in the CR800-Series Specifications Sheet.
Operating Temperature Range
  • -25° to +50°C (standard)
  • Non-condensing environment
Maximum Scan Rate 100 Hz
Analog Inputs 6 single-ended or 3 differential (individually configured)
Pulse Counters 2
Voltage Excitation Terminals 2 (VX1, VX2)
Communications Ports
  • CS I/O
  • RS-232
Switched 12 Volt 1 terminal
Digital I/O
  • Certain digital ports can be used to count switch closures.
  • 4 I/Os or 2 RS-232 COM
    I/O ports can be paired as transmit and receive for measuring smart serial sensors.
Input Limits ±5 V
Analog Voltage Accuracy ±(0.06% of reading + offset) at 0° to 40°C
ADC 13-bit
Power Requirements 9.6 to 16 Vdc
Real-Time Clock Accuracy ±3 min. per year (Correction via GPS optional.)
Internet Protocols FTP, HTTP, XML POP3, SMTP, Telnet, NTCIP, NTP
Communication Protocols PakBus, Modbus, DNP3, SDI-12, SDM
Idle Current Drain, Average 1 mA (@ 12 Vdc)
Active Current Drain, Average
  • 1 to 16 mA (1 Hz sample rate @ 12 Vdc without RS-232 communication)
  • 16 mA (100 Hz sample rate @ 12 Vdc without RS-232 communication)
  • 28 mA (100 Hz sample rate @ 12 Vdc with RS-232 communication)
Dimensions 24.1 x 10.4 x 5.1 cm (9.5 x 4.1 x 2 in.)
Weight 0.7 kg (1.5 lb)

互換性

注意: 以下は代表的な互換性情報を示しています。互換性のある製品や互換性のない製品をすべて網羅したリストではありません。

Software

製品 互換性 注意
LoggerNet (Version 3.3 or higher)
PC200W (リタイア)
PC400 (Version 1.4 or higher)
PCONNECT (リタイア) (Version 3.3 or higher)
PCONNECTCE (リタイア) (Version 2.2 or higher)
RTDAQ
Short Cut
VISUALWEATHER (Version 2 or higher)

互換性に関する追加情報

Sensors

With several channel types, the CR850 is compatible with nearly every available sensor, including thermocouples, SDI-12 sensors, and 4 to 20 mA sensors. A custom ASIC chip expands its pulse count, control port, and serial communications capabilities. The CR850's I/O ports can be paired as transmit and receive, allowing serial communications with serial sensors and devices.

Measurement & Control Peripherals

The CR850 is compatible with all of our CDMs (requires an SC-CPI), SDMs, multiplexers, vibrating-wire interfaces, terminal input modules, and relays. 

Communications

The CR850 communicates with a PC via direct connect, NL201 Ethernet Interface, multidrop modems, short haul modems, phone modems (land line, digital cellular, and voice-synthesized), RF telemetry, and satellite transmitters (Argos and High Data Rate GOES).

Data can be viewed on its onboard keyboard display, CD100 Mountable Display with Keypad, user-supplied iOS or Android device (requires LoggerLink), CD295 DataView II Display, or a user-supplied PDA (PConnect or PConnectCE software required).

The SC115 is the only compatible external data storage device. The CR850 does not have a peripheral port and is therefore not compatible with the CFM100, NL115, or NL120.

Enclosures

The CR850 and its power supply can be housed in any of our standard enclosures. 

Power

Any 12 Vdc source can power the CR850 datalogger. Power supplies commonly used with the CR850 are the BPALK, PS100, and PS200. The BPALK provides eight non-rechargeable D-cell alkaline batteries with a 7.5 A h rating at 20°C.

Both the PS100 and PS200 consist of a sealed rechargeable 7 A h battery and a charging regulator. Their battery should be connected to a charging source (either a wall charger or solar panel). These two power supplies differ in their charging regulator. The PS100 has a standard regulator and the PS200 has a micro-controller-based smart regulator. The PS200's regulator provides two-step constant voltage charging and temperature compensation that optimize battery charging and increases the battery’s life.

Also available are the BP12 and BP24 battery packs, which provide nominal ratings of 12 and 24 A h, respectively. These batteries should be connected to a regulated charging source (e.g., a CH100 or CH200 connected to a unregulated solar panel or wall charger).

Software

CRBasic, the CR850's full programming language, supports simple or complex programming and many onboard data reduction processes.

動画とチュートリアル

ダウンロード

CR800 OS v.32.07 (4.41 MB) 15-05-2024

Execution of this download installs the CR800 Operating System and Compiler on your computer.  It also updates the CR800 support files for the CRBasic Editor.  

Note: This OS has crossed the 2 Meg CR800 size limit for remote download.  The OS must be downloaded to the 2 Meg CR800 via direct connect with the Device Configuration Utility.  All OS download methods are supported by the 4 Meg CR800.

Upgrading from versions prior to version 28 of the Operating System will reset the datalogger’s CPU drive.  This is due to a change in the format of the file system from FAT16 to FAT32.  In order for the datalogger to operate correctly, as part of the upgrade, the CPU drive is formatted to FAT32.  Any programs stored and running from the CPU drive will be lost.  It is not recommended to update the datalogger’s Operating System over a remote connection where program control regulates the communication equipment (turning it on or off, etc.).  In these cases, an on-site visit and a backup using DevConfig’s backup utility is necessary to update the datalogger’s Operating System.

Watch the Video Tutorial: Sending an OS to a Local Datalogger.

In all cases where the datalogger is being updated from an Operating System prior to 28, the use of DevConfig’s backup utility is recommended due to the CPU drive being formatted using the new FAT32 format.

更新履歴をみる

Device Configuration Utility v.2.31 (47.0 MB) 18-12-2024

A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.

Supported Operating Systems:

Windows 11 or 10 (Both 32 and 64 bit)

更新履歴をみる

よくある質問

CR850に関するよくある質問の数: 148

すべて展開すべて折りたたむ

  1. No. The display has its own OS that is not programmable using CRBasic.
  2. Yes, using the DisplayMenu/EndMenu() and MenuItem instructions.
  3. Yes, unless the CR1000 program contains measurement instructions for channels not available on the CR800 or CR850.
  4. Yes. EX and VX are synonymous and refer to voltage excitation.
  5. No. A device is needed that can convert fiber optic to RS-232. Many customers have used products from B&B Electronics for this purpose.
  6. Yes. Many customers use the Iridium satellite transceiver.

ケーススタディ

ルイジアナ州: 陥没穴監視
2012 年 8 月、RESPEC は、ルイジアナ州ナポレオンビル岩塩ドームの西側斜面で発生しつつある陥没穴に現場計測機器と早期警報監視サービスを提供する契約を締結しました。地下深くの塩水洞窟で構造的な亀裂が発生し、周囲の堆積物が洞窟に流れ込み、地表に陥没穴ができ、かき乱された堆積物からガスが放出されました。時間が経つにつれて、陥没穴は 40 エーカー以上に拡大し、最大深度では 400 フィートを超えました。 RESPEC のエンジニアは、発生しつつある陥没穴の周囲の傾斜と水位を継続的に監視するために、リアルタイムの早期警告システムを導入しました。陥没穴は沿岸のヒノキ沼地にあるため、監視システムは過酷な条件 (例: 猛暑、極度の湿度、ハリケーン、大雨、昆虫) で最小限のメンテナンスで稼働する必要がありました。このシステムは、Campbell Scientific のデータ......続きを読む
New Mexico: Meteorological Monitoring at a Mine
Chevron Mining, Inc., (CMI) owned and operated a 6.6 million-metric-ton-per-year (6.6 million-U.S.-ton) molybdenum mining and......続きを読む
サウスダコタ州: 運河を利用した灌漑システム
サウスダコタ州西部のブラックヒルズのすぐ北にある半乾燥地域には、農業に適した広大な台地が広がっています。この地域はさまざまなニーズがあるため、灌漑を注意深く監視する必要があります。ベル フーシェ川の北側の土地は、主に水分を保持する粘り気のあるガンボ土で構成されています。適切な排水が行われないと、余分な水が下層土に浸透し、塩分が表面に上がり、その地域は灌漑できなくなります。一方、ベル フーシェ川の南側の土地は水を多く必要とする砂質ローム土で、頻繁に水やりが必要です。 この地域の複雑な灌漑ニーズを認識し、開拓局はベル フォーシュ灌漑地区 (BFID) を設立しました。BFID は、94 マイルの幹線運河、450 マイルの開放側溝、および複数のダムを使用して、202 km 2 (50,000 エーカー) を超える耕作地に水を供給する灌漑システムの管理、運用、および保守を担当しています。 この地域は度重なる干ばつに見舞われているため、地域全体の灌漑ニーズを満たす十分な水供給を確保するには、節水が不可欠です。BFID は、運河の水位変動を減らし、水の損失を減らして供給効率を高めたいと考えていました。これを実現するには、BFID の運河チェック構造を自動化する必要がありました。 BFID は、プロジェクトの調整、設置、アドバイス、システム構成、およびトラブルシューティングを支援するため、統合コンサルティングおよびサービス会社である......続きを読む
ノースカロライナ州: ALERTステーションを更新
シャーロット・メクレンバーグ洪水情報通知システム (FINS) は、ノースカロライナ州シャーロット周辺の比較的狭い地域に広がる 125 を超える観測所で構成されています。観測所の大部分は降雨量を監視し、残りの観測所は降雨量と水位を監視します。これらの監視所は、事前に設定されたしきい値を超えると、自動ローカル評価リアルタイム (ALERT) プロトコルとアナログ UHF 無線を使用してデータを基地受信機に送信します。  過去には、嵐の際にはパケット衝突と周波数競合により大量のデータが失われていました。ネットワーク全体のパフォーマンスを向上させるために、Distinctive AFWS Designs は、データ スループットを増大し、パケット衝突を減らすことでネットワーク全体の効率を高めるシステムの開発を請け負いました。この目標を達成するために、Distinctive AFWS Designs......続きを読む
メキシコ:6つの空港に自動気象観測所を設置
もちろん、天気は安全で効率的な航空旅行にとって重要な要素です。パイロット、ナビゲーター、航空管制官、整備技術者は皆、航空機と乗客を安全に航空路で移動させるという職務を遂行するために、現在の気象状況を把握する必要があります。 メキシコ航空宇宙航法サービス (SENEAM) は、メキシコの空港に気象データを提供する責任を負っている機関です。この重要な気象データをさらに収集して空港に提供するために、SENEAM は、メキシコの Campbell Scientific 代理店であり、高度な資格を持つインテグレーター兼コンサルタントである Disime と契約し、6 つの空港に総合気象ステーションを設置しました。 標準的な気象条件に加えて、同局は視程測定、特別な滑走路視程 (RVR) 計算、高精度の圧力センサーを必要としていました。Disime は、多数のセンサーと関連するデータの複雑さを処理できる能力を理由に、Campbell Scientific のデータロガーを選択しました。 SENEAM......続きを読む
ニュージーランド: 炭鉱水質監視
ニュージーランドの西海岸では、1870 年代から高品質の石炭が採掘されてきました。採掘作業が環境に与える影響のため、鉱山運営会社の Solid Energy は厳しい要件を満たす必要があります。2007 年、Solid Energy は、14 か所の水質を継続的に監視し、管理とコンプライアンスの目的でライブ データをベース オフィスに送信するプロジェクトに着手しました。また、マンガティーニ川の pH を生態学的に持続可能な状態まで上げるために、石灰注入プラントを自動的に制御するプロジェクトにも着手しました。 スコッテックは、これらの目標を達成するための計測機器の供給と設置を請け負いました。このプロジェクトを困難にしたのは、年間降雨量が約 236 インチであること、地形が険しく、短く急峻な川が洪水時に巨大な岩を崩落させ、その進路にあるものをすべて破壊するなど、いくつかの要因でした。スコッテックは、これらの条件に適した機器を見つける必要がありました。また、あらゆる天候で日常の重要な管理決定に使用できる信頼性の高いテレメトリも必要でした。 測定ステーションの中核をなすのは、Campbell......続きを読む

下記の製品は置き換えられました

Privacy Policy Update

We've updated our privacy policy.  詳細はこちら

Cookie Consent

Update your cookie preferences.  クッキーの設定を更新する