Long-term, trouble-free protection for your data logger
概要
The FC100 is typically used with the SG000 Strike Guard Lightning Detector as part of the CS110 and LW110 lightning warning systems. The SG000 outputs its data signal via fiber-optic cable, and the FC100 is installed at the end of the fiber-optic cable and before the data logger. The FC100 converts a fiber-optic data signal into an RS-232 signal for a lightning-proof connection between the sensor and the data logger.
The FC100 can also be used as an RS-232 link between two serial devices (data logger to PC) separated by less than 100 m (328 ft). The FC100 is a DCE device so a null modem cable will be needed between it and a data logger.
続きを読む利点と特徴
- Lightning-proof and lightning-safe serial communication
- Robust design for long, trouble-free operation
- Instant termination without connectors, crimping, polishing, or epoxy
イメージ
詳細
The FC100 is designed for use with the SG000 Strike Guard lightning detector as part of the CS110 lightning warning system. The SG000 outputs its data signal via fiber-optic cable, and the FC100 is installed at the end of the fiber-optic cable and before the data logger. The FC100 converts a fiber-optic data signal into an RS-232 signal for a lightning-proof connection between the sensor and the data logger.
The FC100 can also be used as an RS-232 link between two serial devices (data logger to PC) separated by less than 328 ft (100 m). The FC100 is a DCE device so a null modem cable will be needed between it and a data logger.
仕様
| Electrical Connector | 9-pin, D sub, DTE compatible |
| Baud Rates | 1,200 to 19,200 bps (at 100 m guaranteed with FC100CBL-L cable) |
| Power | 12 Vdc (via pn 14291 or pn 15966) |
| Current | 5 mA (average) |
| Mounting Holes | 7.62 cm (3 in.) apart |
| Case Width | 2.8 cm (1.1 in.) |
| Dimensions |
|
互換性
注意： 以下は代表的な互換性情報を示しています。互換性のある製品や互換性のない製品をすべて網羅したリストではありません。
Data Loggers
| 製品 | 互換性 | 注意 |
|---|---|---|
| CR1000 (リタイア) | ||
| CR1000X (リタイア) | ||
| CR200X (リタイア) | ||
| CR206X (リタイア) | ||
| CR211X (リタイア) | ||
| CR216X (リタイア) | ||
| CR295X (リタイア) | ||
| CR300 (リタイア) | ||
| CR3000 (リタイア) | ||
| CR310 | ||
| CR350 | ||
| CR5000 (リタイア) | ||
| CR6 | ||
| CR800 (リタイア) | ||
| CR850 (リタイア) | ||
| CR9000X (リタイア) |
互換性に関する追加情報
The FC100 is used with the SG000 Strike Guard.
ドキュメント
よくある質問
FC100に関するよくある質問の数： 10
すべて展開すべて折りたたむ
-
Short-fiber runs sometimes pass too much signal. The solution is to pull the fiber part way out of the holding ferrule.
-
The data transmission fibers are fragile and cannot be bent or broken. Consequently, the fibers need to be handled with care and protected inside a conduit (usually PVC).
-
With a good signal strength, 1200 to 19,200 bps.
-
The 12 Vdc power supply keeps the signal from dropping when large data packets are transmitted.
-
The FC100 provides instant termination—no connectors, crimping, polishing, or epoxy.
-
Direct communication between two RS-232 serial devices, such as a PC to a data logger or a data logger to a serial sensor.
-
100 m (330 ft) with a 1.0 mm poly-methylmethacrylate (PMMA) core with a PVC or polyethylene jacket, simplex or duplex; up to 1 km with a higher-grade fiber.
-
The FC100 is required to communicate with the SG000 Strike Guard Lightning Sensor. The SG000 is an option for the CS110 Electric Field Sensor and the LW110 Lightning Warning System.
-
They provide lightning-proof and lightning-safe serial communication that eliminates the need for transient suppression devices.
-
The FC100 is designed for lightning-proof and lightning-safe serial communication. Because the FC100 offers PMMA or glass fibers that are not conductive, electrical surges (such as those caused by lightning) cannot travel between the modems.
以下に記載
Privacy Policy Update
We've updated our privacy policy. 詳細はこちら
Cookie Consent
Update your cookie preferences. クッキーの設定を更新する