This product is no longer available and has been replaced by: COM220.
| 利用できるサービス | |
|---|---|
| 修理 | 非対応 |
| キャリブレーション | 非対応 |
| フリーサポート | 非対応 |
概要
The COM210 modem enabled communications between a computer and a Campbell data logger via a public switched telephone network. A Hayes-compatible modem was required at the base-station computer while a COM210 was connected to the data logger at the field site. The COM210's wide operating temperature range and minimal power requirements made it ideal for use at remote sites.
続きを読むイメージ
詳細
The COM210 modem enabled communications between a computer and a Campbell data logger via a public switched telephone network. A Hayes-compatible modem was required at the base-station computer while a COM210 was connected to the data logger at the field site. The COM210's wide operating temperature range and minimal power requirements made it ideal for use at remote sites.
Note
Historically, the 10704 Power Adapter was available for connecting the COM210 to the CR500 with s/n 1764 or lower, and the CR10 with the silver or 8032 black wiring panel. The adapter applied a constant 12 V to the COM210's serial I/O. This power adapter is no longer available.
仕様
| Standards | Bell 212A, CCITT V.22, V.32bis |
| FCC Registration | B9QUSA-31402-MM-T |
| Operating Voltage | 12 V |
| Active Current Drain | 160 mA |
| Quiescent Current Drain | 120 μA |
| Baud Rate | 1200, 4800, 9600 bps |
| Operation | Full-duplex over standard analog phone lines |
| Standard Operating Temperature Range | -25° to +50°C |
| Extended Operating Temperature Range | -55° to +85°C |
| Dimensions | 16.0 x 4.3 x 9.1 cm (6.3 x 1.7 x 3.6 in.) with mounts |
| Weight | 272 g (10 oz) |
互換性
注意： 以下は代表的な互換性情報を示しています。互換性のある製品や互換性のない製品をすべて網羅したリストではありません。
Data Loggers
| 製品 | 互換性 | 注意 |
|---|---|---|
| 21X (リタイア) | ||
| CR10 (リタイア) | Not compatible with the CR10's silver or 8032 black wiring panel. Originally the 10704 Power Adapter was used to connect the COM210 to these wiring panels. The 10704 adapter is no longer available. | |
| CR1000 (リタイア) | ||
| CR10X (リタイア) | ||
| CR200X (リタイア) | ||
| CR206X (リタイア) | ||
| CR211X (リタイア) | ||
| CR216X (リタイア) | ||
| CR23X (リタイア) | ||
| CR295X (リタイア) | ||
| CR3000 (リタイア) | ||
| CR500 (リタイア) | Not compatible with CR500s with s/n 1764 or lower. Originally the 10704 Power Adapter was used to connect the COM210 to these data loggers. The 10704 adapter is no longer available. | |
| CR5000 (リタイア) | ||
| CR510 (リタイア) | ||
| CR800 (リタイア) | ||
| CR850 (リタイア) | ||
| CR9000 (リタイア) | Although the CR9000 is compatible, the COM210 does not support its fastest communication rates, and is therefore not practical for most of its applications. | |
| CR9000X (リタイア) | Although the CR9000X is compatible, the COM210 does not support its fastest communication rates, and is therefore not practical for most of its applications. |
互換性に関する追加情報
Power Considerations
The COM210 consumed 120 microAmps quiescent, 160 mA active (max). The data logger's power supply was sufficient for most applications.
Cabling
Data Logger-to-COM210
An SC12 cable was provided for this purpose.
Phone Line-to-COM210
Typically, a length of phone line was run from the telephone company's junction box to the COM210s surge protector, and then to the Ground, Tip, and Ring terminals on the COM210. Alternately, if adequate surge protection was provided by the telephone company and the junction box supports it, a length of telephone wire with RJ11C connectors (#2365) could be run directly from the junction box to the socket on the COM210.
Surge Protection
If the local telephone company did not provide surge protection, either the 6362 or 4330 surge protector needed to be used. See "Ordering Info" tab for more information.
Enclosures
The COM210 required a desiccated, non-condensing environment; a Campbell Scientific enclosure was recommended. Grommets and screws were provided to attach the COM210 to the backplate of our enclosures.
Software
LoggerNet and PC400 software are compatible with the COM210. Both of these software packages provide automated error-checking or user-initiated contacts. LoggerNet also supports scheduled contact times. Our software can run unattended allowing the user to take advantage of lower off-hour telephone rates.
ドキュメント
カタログ
マニュアル
よくある質問
COM210に関するよくある質問の数： 2
-
Yes. We refer to this type of setup as a phone-to-RF base. At the phone-to-RF base, the following are needed: a CS I/O null-modem port (CH100 with A100), a power supply (BP12 or BP24), a radio (RF401), and a phone modem (COM220). Other items are likely needed, such as an enclosure (ENC12/14) and mounting hardware. The phone-to-RF base cannot include a data logger. For details, see Appendix I of the RF401 Instruction Manual.
-
There are several pieces of equipment that are needed to make this work correctly: an installed version of LoggerNet 2.1 or greater, the COM200/COM210, an SC532A, an RS-232 cable, and an SC12 cable.
The first step is to connect everything together correctly. Use the SC12 cable to connect the SC532A to the COM200/COM210 modem. Use the RS-232 cable to connect the other side of the SC532A to the COM port on the computer. Make sure that the computer is powered on and that LoggerNet is up on the screen.
In LoggerNet, select Setup ComPort - Generic Modem 1 - Generic Modem 2. Set the baud rate to 9600 baud. On Generic Modem 1, set RTS low and DTR high.
Using the terminal emulator from the Tools menu of LoggerNet, select Generic Modem 2, and select Open Port. Type AT. The modem will respond with a zero indicating communications are established.
ケーススタディ
西テキサス Mesonet (WTM) プロジェクトは、テキサス工科大学が 1999 年に開始したもので、テキサス州西部のサウス プレーンズ地域の住民にリアルタイムの気象および農業情報を無料で提供しています。ネットワークは成長を続け、現在では高さ 10 メートルの気象観測所 51 基、レーダー ウィンド プロファイラー 1 台、音響ウィンド......続きを読む
過去数年間、電力業界では、ユタ州の天然資源を電力生産にもっと活用しようと奮闘してきました。提案された施設を建設するために必要な許可を得るために、電力会社は、現場の状況を表す最新の気象データと大気質データを使用して、提案された発電所の敷地からの排出物をモデル化する必要があります。Metalotical Solutions, Inc. (MSI) は、ユタ州の提案された発電所または既存の発電所の敷地の基準条件を特徴付ける気象および大気質監視システムを設置して運用しました。最低 1 年間の有効なデータが必要であり、高いデータ回復率を保証するために厳格な品質管理措置が実施されています。データは、Campbell Scientific CR23X データロガーを使用して 1 秒値から計算された 15 分間の平均値として収集および保存されます。信頼性の高い固定電話または携帯電話接続により、設置されたデータロガーを頻繁に照会してデータを取得し、データの有効性を確認することができます。Campbell Scientific......続きを読む
Privacy Policy Update
We've updated our privacy policy. 詳細はこちら
Cookie Consent
Update your cookie preferences. クッキーの設定を更新する