RETIRED ›
This product is no longer available and has been replaced by: CS475A-L.
CS475-L Radar Water-Level Sensor, 65 ft Maximum Distance
利用できるサービス

概要

The CS475 is a radar-ranging sensor that monitors water level of rivers, lakes, tidal seas, and reservoirs. It can measure distances up to 20 meters. The CS475 outputs a digital SDI-12 signal to indicate distance and stage. Many of our data loggers can read the SDI-12 signal.

続きを読む

利点と特徴

  • FCC approved for outdoor use (FCC ID number MOIPULS616263)
  • Ideal for areas where submersed sensors can be damaged due to corrosion, contamination, flood-related debris, lightning, or vandalism
  • Compatible with most Campbell Scientific data loggers
  • Low maintenance—no moving parts significantly reduces maintenance cost and time
  • Low power consumption
  • Rugged enough for harsh environments—NEMA rated 4X
  • Wide operating temperature range (-40° to +80°C)

イメージ

詳細

The CS475 emits short microwave pulses and then measures the elapsed time between the emission and return of the pulses. The elapsed time measurement is used to calculate the distance between the sensor and the target (e.g., water, grain, slurry). The distance value can then be used to determine depth.

仕様

Compliance FCC approved for outdoor use (FCC IC number M01PULS616263)
Measurement Range 50 mm to 20 m (2 in. to 65 ft)
Accuracy ±5 mm (±0.2 in.) over entire measurement range
Resolution 1 mm (0.04 in.)
Output Options SDI-12
Radar Frequency ~26 GHz
Electromagnetic Compatibility Emission to EN 61326; Electrical Equipment Class B
Pulse Energy 1 mW maximum
Beam Angle 10°
Input Voltage 9.6 to 16 Vdc
Surge Protection 1.5 KVA
Operating Temperature Range -40° to +80°C
Temperature Sensitivity
  • Average TK is 2 mm/10 K
  • Maximum 5 mm (over the entire temperature range of -40° to +80°C)
Vibration Resistance Mechanical vibrations with 4 g and 5 to 100 Hz
Housing Rating NEMA 4x
Housing Material Aluminum, coated IP66/68
Horn Material PVDF encapsulated plastic
Typical Sleep Current Drain 4.7 mA (with 12 V power supply)
Typical Measurement Current Drain 14 mA (with 12 V power supply)
Side Cap Diameter 8.6 cm (3.4 in.)
End Cap Diameter 8.6 cm (3.4 in.)
Horn Diameter 7.5 cm (3 in.)
Head Width 11 cm (4.3 in.)
Horn Length 13.7 cm (5.4 in.)
Total Length 26.6 cm (10.5 in.)
Weight
  • 1.7 kg (3.8 lb) without bracket
  • 2.3 kg (5 lb) with bracket

互換性

注意: 以下は代表的な互換性情報を示しています。互換性のある製品や互換性のない製品をすべて網羅したリストではありません。

Data Loggers

製品 互換性 注意
21X (リタイア)
CR10 (リタイア)
CR1000 (リタイア)
CR10X (リタイア)
CR200X (リタイア)
CR206X (リタイア)
CR211X (リタイア)
CR216X (リタイア)
CR23X (リタイア)
CR295X (リタイア)
CR300 (リタイア)
CR3000 (リタイア)
CR500 (リタイア)
CR5000 (リタイア)
CR510 (リタイア)
CR800 (リタイア)
CR850 (リタイア)
CR9000 (リタイア)
CR9000X (リタイア)

よくある質問

CS475-Lに関するよくある質問の数: 4

すべて展開すべて折りたたむ

  1. Yes. In the Water | Level & Flow folder, there is the option to select CS475/CS476/CS477 Radar Water Level Sensor. Click to move the selection to the Selected device window, and enter the SDI-12 address.

  2. すべてのセンサに異なるケーブル終端オプションがあるわけではありません。特定のセンサで利用可能なオプションは、センサ製品ページの注文情報エリアの 2 つの場所で確認できます。

    モデル番号
    ケーブル終端オプション リスト
    センサが –ET、–ETM、–LC、–LQ、または –QD バージョンで提供されている場合、そのオプションが利用可能かどうかはセンサモデル番号に反映されます。たとえば、034B は 034B-ET、034B-ETM、034B-LC、034B-LQ、および 034B-QD として提供されています。

    その他のすべてのケーブル終端オプション (利用可能な場合) は、センサ製品ページの注文情報エリアの「ケーブル終端オプション」の下にリストされています。たとえば、034B-L 風力発電セットは、034B-L 製品ページの注文情報エリアに示されているように、–CWS、–PT、および –PW オプションで提供されています。

    注意: 新しい製品が在庫に追加されると、通常は複数のモデル番号を作成するのではなく、1 つのセンサモデルの下に複数のケーブル終端オプションをリストします。たとえば、HC2S3-L には、HC2S3-LC モデルではなく、CS110 に接続するための –C ケーブル終端オプションがあります。

  3. Most Campbell Scientific sensors are available as an –L, which indicates a user-specified cable length. If a sensor is listed as an –LX model (where “X” is some other character), that sensor’s cable has a user-specified length, but it terminates with a specific connector for a unique system:

    • An –LC model has a user-specified cable length for connection to an ET107, CS110, or retired Metdata1.
    • An –LQ model has a user-specified cable length for connection to a RAWS-P weather station.

    If a sensor does not have an –L or other –LX designation after the main model number, the sensor has a set cable length. The cable length is listed at the end of the Description field in the product’s Ordering information. For example, the 034B-ET model has a description of “Met One Wind Set for ET Station, 67 inch Cable.” Products with a set cable length terminate, as a default, with pigtails.

    If a cable terminates with a special connector for a unique system, the end of the model number designates which system. For example, the 034B-ET model designates the sensor as a 034B for an ET107 system.

    • –ET models terminate with the connector for an ET107 weather station.
    • –ETM models terminate with the connector for an ET107 weather station, but they also include a special system mounting, which is often convenient when purchasing a replacement part.
    • –QD models terminate with the connector for a RAWS-F Quick Deployment Station.
    • –PW models terminate with the connector for a PWENC or pre-wired system.
  4. Many Campbell Scientific sensors are available with different cable termination options. These options include the following:

    • The –PT (–PT w/Tinned Wires) option is the default option and does not display on the product line as the other options do. The cable terminates in pigtails that connect directly to a data logger.
    • In the –C (–C w/ET/CS110 Connector) option, the cable terminates in a connector that attaches to a CS110 Electric Field Meter or an ET-series weather station.
    • In the –CWS (–CWS w/CWS900 Connector) option, the cable terminates in a connector that attaches to a CWS900-series interface. Connection to a CWS900-series interface allows the sensor to be used in a wireless sensor network.
    • In the –PW (–PW w/Pre-Wire Connector) option, the cable terminates in a connector that attaches to a prewired enclosure.
    • In the –RQ (–RQ w/RAWS Connector) option, the cable terminates in a connector that attaches to a RAWS-P Permanent Remote Automated Weather Station.

    Note: The availability of cable termination options varies by sensor. For example, sensors may have none, two, or several options to choose from. If a desired option is not listed for a specific sensor, contact Campbell Scientific for assistance.

ケーススタディ

South Africa: Transforming a Polluted River
The Jukskei River is one of the largest rivers in Johannesburg, South Africa. The river......続きを読む
Panama: Turbidity in Mine Runoff
Water and Earth Technologies (WET), a Campbell Scientific integrator, is a water resources and environmental engineering firm.......続きを読む

Privacy Policy Update

We've updated our privacy policy.  詳細はこちら

Cookie Consent

Update your cookie preferences.  クッキーの設定を更新する