利用できるサービス | |
---|---|
修理 | 対応 |
キャリブレーション | 非対応 |
フリーサポート | 対応 |
The NL120 allows the data logger to communicate over a local network or a dedicated Internet connection via TCP/IP. This small, rugged communication device connects directly to the 40-pin peripheral port on a CR1000 or CR3000 datalogger.
続きを読むThe NL120 uses a straight through cable when the cable is run from a hub to the NL120. A 10baseT Ethernet crossover cable is used if the cable is run directly from the computer to the NL120. For cable lengths longer than 9 feet, either a shielded 10baseT Ethernet cable or the 28033 surge protector needs to be used.
The NL120 is set up using the Device Configuration utility (DevConfig). DevConfig is bundled with our PC400, RTDAQ, and LoggerNet software and is available, at no charge, from: www.campbellsci.com/downloads
Power Requirements | 12 V (supplied through the data logger’s peripheral port) |
Ethernet Speed | 10Base-T (10 Mbps), half-duplex |
Typical Current Drain | 20 mA |
Dimensions | 10.2 x 6.4 x 2.8 cm (4.0 x 2.5 x 1.1 in.) |
Weight | 66.62 g (2.35 oz) |
EMI and ESD Protection |
|
European Standards | Meets requirements for a class A device under European Standards. |
Application of Council Directive(s) | 89/336/EEC as amended by 89/336/EEC and 93/68/EEC |
Standards to Which Conformity Is Declared | EN55022-1; 1995 and EN50082-1: 1992 |
Software Requirements |
|
LoggerNet | Version 3.2 or later |
PC400 | Version 1.3 or later |
DevConfig | Version 1.5 or later |
注意: 以下は代表的な互換性情報を示しています。互換性のある製品や互換性のない製品をすべて網羅したリストではありません。
製品 | 互換性 | 注意 |
---|---|---|
CR1000 (リタイア) | ||
CR200X (リタイア) | ||
CR206X (リタイア) | ||
CR211X (リタイア) | ||
CR216X (リタイア) | ||
CR295X (リタイア) | ||
CR3000 (リタイア) | ||
CR5000 (リタイア) | ||
CR800 (リタイア) | ||
CR850 (リタイア) | ||
CR9000X (リタイア) |
製品 | 互換性 | 注意 |
---|---|---|
ENC10/12 | ||
ENC10/12R | CR1000またはCR3000に取り付け | |
ENC12/14 | CR1000に取り付け | |
ENC14/16 | CR1000またはCR3000に取り付け | |
ENC16/18 | Attached to a CR1000 or CR3000 |
A 10baseT Ethernet straight through cable is used when the cable is run from a hub to the NL120. A 10baseT Ethernet crossover cable is used if the cable is run directly from the computer to the NL120. For cable length longer than 9 ft, the 10baseT Ethernet cable must be shielded or the 28033 surge suppressor must be used.
The NL120 fastens onto the data logger's 40-pin peripheral port. This means that the NL120 is only compatible with the CR1000 and CR3000. It is NOT compatible with the CR800, CR850, CR200X, CR5000, or CR9000X dataloggers.
NL120に関するよくある質問の数: 23
すべて展開すべて折りたたむ
The NL120 is a communications peripheral only. It does not provide additional analog terminals for a data logger.
Yes, the NL120 can be repaired. Refer to the Repair and Calibration page for the process of returning equipment to Campbell Scientific.
The PakBus protocol allows multiple simultaneous connections. The PakBus address that LoggerNet uses for itself on one of the PCs needs to be changed, though.
There is no separate firmware for the NL120. It is built into the main data logger’s operating system.
No. The NL120 is used for one device only.
No. Configurations can be changed, however, via any other mode of communication with the data logger.
We've updated our privacy policy. 詳細はこちら
Update your cookie preferences. クッキーの設定を更新する