風向風速計 / 05106-L
RETIRED ›
This product is no longer available and has been replaced by: 05108-L.
05106-L Wind Monitor, Marine Version
利用できるサービス
修理 対応
キャリブレーション 非対応
フリーサポート 対応

概要

Designed for offshore and marine applications, the 05106 is a lightweight, robust instrument that measures wind speed and direction. Manufactured by R. M. Young, this wind monitor is cabled for use with Campbell Scientific data loggers.

続きを読む

利点と特徴

  • Waterproof bearing lubricant and a sealed, heavy-duty cable pigtail instead of the standard junction box make it more durable at marine and off-shore locations
  • Compatible with most Campbell Scientific data loggers
  • Rugged enough for harsh environments
  • Constructed with thermoplastic material that resists corrosion from sea-air environments and atmospheric pollutants
  • Compatible with the LLAC4 4-channel Low-Level AC-Conversion Module, which increases the number of anemometers one data logger can measure
  • Uses stainless-steel, precision-grade ball bearings for the propeller shaft and vertical shaft bearings
  • Compatible with the CWS900-series interfaces, allowing it to be used in a wireless sensor network

イメージ

詳細

The 05106 Wind Monitor-MA is made out of rigid UV-stabilized thermoplastic with stainless steel and anodized aluminum fittings. The thermoplastic material resists corrosion from sea air environments and atmospheric pollutants. It uses stainless-steel precision-grade ball bearings for the propeller shaft and vertical shaft bearings.

To make it more durable in offshore and marine applications, the 05106 has waterproof bearing lubricant and a sealed, heavy-duty cable pigtail instead of the standard junction box.

The 05106 measures wind speed with a helicoid-shaped, four-blade propeller. Rotation of the propeller produces an ac sine wave that has a frequency directly proportional to wind speed. The ac signal is induced in a transducer coil by a six-pole magnet mounted on the propeller shaft. The coil resides on the non-rotating central portion of the main mounting assembly, eliminating the need for slip rings and brushes.

Wind direction is sensed by the orientation of the fuselage-shaped sensor body, which is connected to an internal potentiometer. The data logger applies a known precision excitation voltage to the potentiometer element. The output is an analog voltage signal directly proportional to the azimuth angle.

仕様

Operating Temperature Range -50° to +50°C (assuming non-riming conditions)
Mounting Pipe Description
  • 34 mm (1.34 in.) OD
  • Standard 1.0-in. IPS schedule 40
Propeller Diameter 18 cm (7.1 in.)
Overall Height 37 cm (14.6 in.)
Overall Length 55 cm (21.7 in.)
Main Housing Diameter 5 cm (2.0 in.)
Weight 1.5 kg (3.2 lb)

Wind Speed

Range 0 to 100 m/s (0 to 224 mph)
Accuracy ±0.3 m/s (0.6 mph) or 1% of reading
Starting Threshold 1.1 m/s (2.4 mph)
Distance Constant 2.7 m (8.9 ft) 63% recovery
Output ac voltage (three pulses per revolution)

90 Hz (1800 rpm) = 8.8 m/s (19.7 mph)
Resolution (0.0980 m s-1)/(scan rate in seconds) or (0.2192 mph)/(scan rate seconds)

Wind Direction

Mechanical Range 0 to 360°
Electrical Range 355° (5° open)
Accuracy ±3°
Starting Threshold 1.1 m/s (2.4 mph) at 10° displacement
Distance Constant 1.3 m (4.3 ft) 50% recovery
Damping Ratio 0.3
Damped Natural Wavelength 7.4 m (24.3 ft)
Undamped Natural Wavelength 7.2 m (23.6 ft)
Output
  • Analog dc voltage from potentiometer (resistance 10 kohm)
  • Linearity is 0.25%.
  • Life expectancy is 50 million revolutions.
Voltage Power switched excitation voltage supplied by data logger

互換性

注意: 以下は代表的な互換性情報を示しています。互換性のある製品や互換性のない製品をすべて網羅したリストではありません。

Data Loggers

製品 互換性 注意
21X (リタイア)
CR10 (リタイア)
CR1000 (リタイア)
CR1000X (リタイア)
CR10X (リタイア)
CR200X (リタイア)
CR206X (リタイア)
CR211X (リタイア)
CR216X (リタイア)
CR23X (リタイア)
CR295X (リタイア)
CR300 (リタイア)
CR3000 (リタイア)
CR310
CR500 (リタイア) Measurements are typically processed for output with the Wind Vector instruction, which is not present in the CR500.
CR5000 (リタイア)
CR510 (リタイア)
CR800 (リタイア)
CR850 (リタイア)
CR9000 (リタイア) Measurements are typically processed for output with the Wind Vector instruction, which is not present in the CR9000.
CR9000X (リタイア)

互換性に関する追加情報

Mounting

The Wind Monitors can be attached to a CM202, CM204, or CM206 crossarm via a 17953 NU-RAIL fitting or CM220 Right Angle Mounting Bracket. Alternatively, the Wind Monitors can be attached to the top of our stainless-steel tripods via the CM216 Sensor Mounting Kit.

Wind Profile Studies

Wind profile studies measure many wind sensors. For these applications, the LLAC4 4-Channel Low Level AC Conversion Module can be used to increase the number of Wind Monitors measured by one data logger. The LLAC4 allows data logger control ports to read the wind speed sensor’s ac signals instead of using pulse channels. Data loggers compatible with the LLAC4 are the CR200(X) series (ac signal ≤1 kHz only), CR800, CR850, CR1000, CR3000, and CR5000.

Data Logger Considerations

The 05106's propeller uses one pulse count channel on the data logger. Its wind vane requires one single-ended channel and access to an excitation channel (the excitation channel can be shared with other high impedance sensors).

Programming

The 05106's propeller is measured by the PulseCount Instruction in CRBasic and by Instruction 3 (Pulse Count) in Edlog. The wind vane is measured by the BrHalf Instruction in CRBasic and by Instruction 4 (Excite-Delay-SE) in Edlog. The measurements are typically processed for output with the Wind Vector instruction (not present in the CR500 or CR9000 but is present in the CR9000X).

動画とチュートリアル

よくある質問

05106-Lに関するよくある質問の数: 13

すべて展開すべて折りたたむ

  1. Campbell Scientific does not sell an extension cable. A replacement cable can be ordered and built to the desired length (pn 05106CBL-L). This replacement cable has a connector that mates with the connector at the end of the 3 ft cable attached to the 05106-L.

  2. 何が壊れているかによって異なります。通常、Campbell Scientific はユニットを修理できるため、ユーザーは新しいものを購入する必要はありません。

  3. 測定手順はおそらく同じままです。ただし、乗数とオフセットに加えて、風速に応じてパルスの種類が変わる場合があり、風向に応じて励起電圧が変わる場合があります。データロガーのプログラミング方法については、取扱説明書を参照してください。

  4. 概算で約0.01 mA 未満です。風速信号には電力は必要ありません。風向は、5 Vdc で励起されたときに最大 0.5 mA しか使用せず、その後は測定ごとに 0.016 秒間だけオンになります。風向が 1 秒ごとに測定される場合 (通常)、平均電流消費は 0.01 mA 未満です。

  5. 風向風速計の方向付けは、データロガーがプログラムされ、真北の位置が決定された後に行われます。真北は通常、磁気コンパスを読み取り、磁気偏角の補正を適用することで見つけられます。ここで、磁気偏角は、真北と磁北の間の度数です。特定の場所の磁気偏角は、USFA マップ、地元の空港、またはコンピュータ サービスから取得できます。

  6. キャリブレーション シートに含まれる情報は、センサごとに異なります。一部のセンサでは、シートにデータロガーをプログラムするために必要な係数が含まれています。その他のセンサでは、キャリブレーション シートは合格/不合格レポートです。

  7. すべてのセンサに異なるケーブル終端オプションがあるわけではありません。特定のセンサで利用可能なオプションは、センサ製品ページの注文情報エリアの 2 つの場所で確認できます。

    モデル番号
    ケーブル終端オプション リスト
    センサが –ET、–ETM、–LC、–LQ、または –QD バージョンで提供されている場合、そのオプションが利用可能かどうかはセンサモデル番号に反映されます。たとえば、034B は 034B-ET、034B-ETM、034B-LC、034B-LQ、および 034B-QD として提供されています。

    その他のすべてのケーブル終端オプション (利用可能な場合) は、センサ製品ページの注文情報エリアの「ケーブル終端オプション」の下にリストされています。たとえば、034B-L 風力発電セットは、034B-L 製品ページの注文情報エリアに示されているように、–CWS、–PT、および –PW オプションで提供されています。

    注意: 新しい製品が在庫に追加されると、通常は複数のモデル番号を作成するのではなく、1 つのセンサモデルの下に複数のケーブル終端オプションをリストします。たとえば、HC2S3-L には、HC2S3-LC モデルではなく、CS110 に接続するための –C ケーブル終端オプションがあります。

  8. Campbell Scientific のセンサのほとんどは、ユーザー指定のケーブル長を示す –L として提供されています。センサが –LX モデル (「X」は他の文字) としてリストされている場合、そのセンサのケーブルの長さはユーザー指定ですが、固有のシステム用の特定のコネクタで終端されます。

    • -LC モデルには、ET107、CS110、または廃止された Metdata1 に接続するためのユーザー指定のケーブル長があります。
    • -LQ モデルには、RAWS-P 気象ステーションに接続するためのユーザー指定のケーブル長さがあります。

    センサのメイン モデル番号の後に –L または –LX の指定がない場合、センサのケーブル長は設定されています。ケーブル長は、製品の注文情報の説明フィールドの末尾に記載されています。たとえば、034B-ET モデルの説明は、「ET ステーション用 Met One Wind セット、67 インチ ケーブル」です。ケーブル長が設定されている製品は、デフォルトでバラ線で終端されます。

    ケーブルが特定のシステム用の特別なコネクタで終端されている場合、モデル番号の末尾でそのシステムを指定します。たとえば、034B-ET モデルは、ET107 システムのセンサを 034B として指定します。

    • –ET モデルは、ET107 気象ステーション用のコネクタです。
    • –ETM モデルは ET107 気象ステーション用のコネクタですが、交換部品を購入するときに便利な特別なシステム マウントも含まれています。
    • –QD モデルは、RAWS-F クイック展開ステーション用のコネクタです。
    • –PW モデルは、PWENC または配線済みシステム用のコネクタです。
    1. Short Cutを使用して、[Outputs] 画面の [Selected Sensors] リストで該当する風向センサをクリックします。
    2. 有効な 2 つの出力オプションは SampleWindVector です。WindVector を選択します。
    3. WindVector 命令には出力オプションがあります。平均風向を含むオプションを選択してください。

ケーススタディ

デラウェア州: 環境観測システム
デラウェア環境観測システム (DEOS) は、デラウェア州、沿岸水域、デラウェア湾、およびメリーランド州、ペンシルベニア州、ニュージャージー州の隣接地域の環境状況をリアルタイムで監視するシステムです。DEOS は、デラウェア州およびデラウェア半島全域の緊急事態管理、天然資源監視、農業、輸送、およびその他の活動に携わる意思決定者のためのツールです。これは、多数の州および連邦政府機関との共同事業であり、その視覚化および分析ツールの多くは、デラウェア州外でも適応できるように設計されています。 DEOS は次の要素で構成されています。 DEMON - DEOS 環境監視および観測ネットワークは、デラウェア州およびその周辺の気象観測地点のネットワークです。 DIVAS - DEOS 統合視覚化および分析システムは、地上気象観測と NWS WSR-88D レーダーの降水量推定を統合します。これにより、ESRI......続きを読む
イスラエル:紅海の海洋気象
イスラエルのエイラートにある大学間海洋科学研究所 (IUI) の気象観測所では、海岸と外洋の両方で以下の継続的な測定が行われています。 気温 相対湿度 風速と風向 水温 さらに、沿岸観測所では気圧、太陽放射、海面(水圧を測定することによって)を測定します。 システムの説明 すべての測定値は、観測所のデータロガーによって収集されます。水位を除くすべての変数は、1 秒間隔でサンプリングされます (水位の値は 1 分間隔でサンプリングされます)。 計測値は 10 分間の平均で算出され、専用コンピュータが 1 時間ごとに平均値を取得します。データは Meteo-Tech のサーバー......続きを読む
アラスカ: ボートの安全
Campbell Scientificの CR10X は、アラスカ南東部の海岸に設置されたユニークな気象観測所プロジェクトの中核です。ピーターズバーグの小さなコミュニティは、アラスカの険しい海岸山脈の主要河川であるスティキーン川デルタの近くにあります。スティキーン デルタは、レクリエーションや自給自足の活動に人気のエリアですが、異常で驚くべき気象パターンでも有名です。国立気象局は、この地域に気象観測所も観測所もありません。 ボートの安全を促進するため、アラスカ州ピーターズバーグのボランティア消防署捜索救助隊が、川のデルタ地帯に気象観測所を設置するプロジェクトを主導しました。この観測所は、市内の電話番号で簡単に呼び出すことができ、リアルタイムの風速を 45 秒間の音声アナウンスで伝えます。最も重要なのは、アナウンスに風の傾向を判断するための簡単なヒストグラムが含まれていることです。捜索救助隊のボランティアでプロジェクト コーディネーターのジョン マーガス氏は、「スティキーン デルタ地帯のリアルタイムの風速と風向にすばやく簡単にアクセスできるため、ボート乗りはより情報に通じ、ボートの安全に関するより適切な判断を下すことができます」と述べています。 気象観測所は有線電話サービスが利用できる範囲にはありませんが、電話システムへの音声リンクを提供する地元の携帯電話サービスの範囲内にあります。Campbell Scientificの COM300 電話モデムと音声合成装置は、モトローラの携帯電話トランシーバーとペアになっています。Campbell Scientificが供給する RM......続きを読む

Privacy Policy Update

We've updated our privacy policy.  詳細はこちら

Cookie Consent

Update your cookie preferences.  クッキーの設定を更新する